Download the SA_U403.zip file.

This zip file contains 3 files.

Put these onto floppy disks, labeled 1 and 2, with Setup.exe on disk 1 and Setup.w02 on disk 2.

Insert disk 1, and run "setup.exe".

This will bring you up to SCADAlarm version 4.03.

• The Allow Ack to SCADA Acknowledgement option does not function properly. You must use Allow Ack from SCADA or Allow Both
• Accessing Driver Configuration window or clicking "Play" from the Tag Script builder while an alpha page is in progress causes a lock up.
• Log to Printer option causes sluggish behavior if printer disconnected, powered down, or offline.
• The edit box for Pager Formats doesn’t scroll (limited to 150chars)—therefore, it’s easy to fill it without actually reaching the character limit of the pager.
• On-the-fly changes to an Operator’s Calling Prefs should be allowed. However, it has been reported that extensive schedule changes aren’t always detected. Restarting SCADAlarm will enable schedule changes.

• SCADAlarm hardware isn’t compatible with multi-port I/O expander cards that share IRQs. 
• 3com Internal modem volume adjustment (via S46 register) affects local annunciation volume and telephone line volume, unlike the external, which affects only local speaker volume.

• SCADAlarm now properly releases system resources when attempting to reinitialize DDE for a failed DDE Server. It is still strongly suggested that a "DDE Status" tag(s) (pg. 46 in the Users Manual) be configured that will call a network administrator on failure of the DDE to each DDE Server in your system. Also, failed nodes are not retried constantly anymore (now it’s every 5 seconds).
• The Holiday Schedule feature now works properly. SCADAlarm would use the Control Schedule for the current weekday instead of the user programmed Holiday Schedule.
• Pager Message Formats had a problem handling incompletely defined placeholders. A placeholder variable with an opening "[" followed by only 1 additional character would cause SCADAlarm to lock up. This has been fixed.

• Alphanumeric Paging logic is now more immune to differences between paging service providers. Receive buffer flushed after "ID=" found.

• Alarm/Tag point definition: edit boxes properly retain selections when selecting custom ON. VOX and OFF .VOX files.
• Local Annunciation: if a higher priority alarm is detected by SCADAlarm, it will attempt to locally annunciate the alarm immediately, instead of waiting for the Local Annunciation Delay to expire. This has been fixed.
• Record window "Done" button could be pressed prematurely, placing modem in indeterminate state. This has been fixed.

• Tag Report Scripts: Select-a-Report window now remembers last selected report. Previous versions would always show the report list with the first report highlighted.
• Tag Report Scripts: Select-an-Alarm-Tag window no longer displays tags that already have tag report scripts built for them.
• Acknowledge All window is larger, allowing users to see text on long tagnames and descriptions.
• Blind Dialing (‘N’) helps with acceptance of non-standard dialtones.
• On global system re-enable (by DDE, timeout, or operator pushbutton) ‘0’ is poked back to ALL disable tags.

• The Login PIN number entry window Cancel button works again.
• SCADAlarm no longer allows exit without warning from telephone conversation if unacknowledged alarms are present in your group. Formerly, only the current target operator in a group was warned.
• When updating the file formats from earlier versions of SCADAlarm, the conversion now succeeds even if some files (ALRMLIST.CAR, ALRMSCRP.CAR) don’t exist; however, OPERATOR.CAR must exist.
• SCADAlarm now no longer speaks "This List is Empty", even though it isn’t empty. This would happen when alarms had delays specified, but "Immediate Alarms" were scheduled.
• The failed-hardware detection now works if the suspicion sequence is triggered by an alarm. Before, it worked only if triggered by a routine test (every 10 minutes).

• Font size for the "Link Alarm to Script" window and several others has been decreased from 10-point to 8-point, for customers with only 640x480 display capability.
• In the DDE Server Popup, the Server Name and Topic Name fields are now 128 bytes long.
• From "Link Alarm to Script", you are now able to select existing .VOX files even if no hardware is available.
• The tag description may now be displayed in the logfile, along with tagname, by editing the SCADALRM.INI file in the windows root directory.
• There is now a descriptively named flag in SCADALRM.INI that allows user to disable the appearance .VOX files Audition request box.

• Internal Hayes modems are now detected properly

• None

• None

• Alarm Grouping
• Alarm Delays, Priorities
• Ack on Delivery, Ack on Clear
• Multiple DDE Servers
• System Tags (HW Fail, DDE Server Fail, Enable/Disable SCADAlarm, Bad Phone Line, etc.)
• Operator Scheduling
• Voice Pager Support
• Adjustable ring count for answering
• Scheduled System Test
• MAX Length of voxfiles extended to 120 sec from 15 sec
• Raw data values allowed in alpha pager formats
• Import/Export to .CSV for tags only